Controls and Automation Engineering

The working kit of a controls and automation engineer: an instrument index you trust, loops that stay in automatic, alarms operators can act on, cause and effect charts, safety system bypasses under control and clean loop checks.

Free · Mac (Apple silicon) and Windows · v1.0.5 · Other platforms

Then open the Marketplace in the app, search for Controls and Automation Engineering, and click Install. It goes into your own files, and works offline from then on.

Before you start: this plan is general information to help you organise your own work. It does not replace your professional judgement, the rules of your regulator or professional body, your firm's policies, or advice from a qualified lawyer, accountant or other adviser. Where a law, code or standard applies, use the current official version for your country, and get qualified sign-off on regulated or safety-critical work.

What it installs.

1

Pillar

1

Area

50

Projects

207

Starter tasks

🔧 Engineering Practice

Controls and Automation Engineering

Working as a controls and automation engineer: instrumentation, control loops and tuning, cause and effect charts, safety systems, alarm management and loop checks.

  1. Controls and instrumentation standards shelf
  2. Reading P&IDs and ISA instrument tags fluently
  3. Instrument index and loop list baseline
  4. Control system architecture map
  5. Instrumentation and control design basis
  6. Hazardous area instrument certification check
  7. Control loop performance baseline survey
  8. Alarm system performance baseline
  9. Cause and effect chart register
  10. Weekly loops in manual review
  11. Monthly bad actor alarm review
  12. Safety system bypass and override register
  13. Instrument calibration programme and as-found records
  14. Control system backup and restore routine
  15. Weekly control system health check
  16. Online analyser validation routine
  17. Instrument obsolescence and critical spares watch
  18. Alarm and trip setpoint change register
  19. Control valve health monitoring with smart positioners
  20. Gas detector testing and fault follow-up
  21. PID fundamentals and controller algorithm forms
  22. Step testing and lambda tuning a real loop
  23. Cascade, ratio and feedforward control strategies
  24. Control valve sizing and selection
  25. Flow measurement technology selection
  26. Level and pressure measurement pitfalls
  27. Intrinsically safe loop verification
  28. HART and fieldbus diagnostics in practice
  29. Temperature measurement and thermowell checks
  30. Control narrative for a process unit
  31. Writing the site alarm philosophy
  32. Alarm rationalisation of one process unit
  33. Retuning the ten worst loops
  34. Standardising on a transmitter range
  35. Wireless instrumentation trial
  36. Control valve stiction diagnosis
  37. Spurious trip reduction review
  38. Loop check campaign for a new installation
  39. Interlock and trip function test before start-up
  40. Control system migration cutover
  41. Hurricane season control system readiness
  42. Operator briefing for a new control strategy
  43. First 90 days as a site controls engineer
  44. From instrument technician to controls engineer
  45. Controls engineer at a system integrator
  46. Sole controls engineer on a small plant
  47. Automation professional certification plan
  48. Model predictive control upkeep
  49. Gas detector coverage mapping review
  50. Compressor anti-surge control review

Where it starts.

Each project arrives with its purpose, milestones and first tasks written out. Here is how the first three read.

Controls and instrumentation standards shelf

Arguments about tag letters, alarm priorities or safety system bypasses usually end at a clause number, so a controls engineer needs the right editions to hand. A short, current shelf covering ISA-5.1 symbols, IEC 61511 or ISA 84 for safety instrumented systems, ISA-18.2 or IEC 62682 and EEMUA 191 for alarms, and the IEC 60079 family for hazardous areas means every design note and review comment can cite its source.

First tasks

  • Ask your lead which controls standards and site specifications apply here
  • Check the edition of each standard named in the current project scope
  • Confirm access to each document through the library or subscription
  • Write a one-page index of which standard answers which question

Reading P&IDs and ISA instrument tags fluently

Every loop check, alarm review and cause and effect chart starts from the piping and instrumentation diagram, and a misread function letter sends people to the wrong device. Learning the ISA-5.1 identification letters, the bubble and line symbols, and your site's local conventions until you can trace any loop from sensor to final element without the legend open saves hours on every job that follows.

First tasks

  • Print the legend sheet from your site P&ID set and mark unfamiliar symbols
  • Decode twenty tags from one P&ID without looking at the legend
  • Trace five control loops end to end and have a senior engineer check them
  • Write a crib sheet of local conventions that differ from ISA-5.1

Instrument index and loop list baseline

The instrument index is the master list everything else hangs from: calibration ranges, alarm limits, loop drawings, spares and hazardous area certificates all key off the tag. On older sites it drifts from reality as devices are swapped and ranges changed, so a baseline that reconciles the index against the control system database and the field gives you a list you can actually work from.

First tasks

  • Export the instrument index for one process unit into a working copy
  • Export the matching point list from the control system database
  • Match the two lists by tag and flag missing and orphan entries
  • Walk the unit and check twenty devices against the index
  • Raise each discrepancy through the document change route

Make it yours.

Install Controls and Automation Engineering, then tell Aurum the date you're aiming for. It checks whether the plan fits the weeks you actually have.

Free · Mac (Apple silicon) and Windows · v1.0.5 · Other platforms

Blueprints are general information to help you organise your own work. They are not medical, financial, legal or other professional advice. See the Terms.