Process Simulation Modelling

Process simulations people can trust: a written model basis, the right thermodynamics, flowsheets that converge, models kept matched to plant data, and the case studies, debottlenecking and dynamic work that decisions rest on.

Free · Mac (Apple silicon) and Windows · v1.0.5 · Other platforms

Then open the Marketplace in the app, search for Process Simulation Modelling, and click Install. It goes into your own files, and works offline from then on.

Before you start: this plan is general information to help you organise your own work. It does not replace your professional judgement, the rules of your regulator or professional body, your firm's policies, or advice from a qualified lawyer, accountant or other adviser. Where a law, code or standard applies, use the current official version for your country, and get qualified sign-off on regulated or safety-critical work.

What it installs.

1

Pillar

1

Area

50

Projects

200

Starter tasks

🔧 Engineering Practice

Process Simulation Modelling

Building process simulations in tools such as Aspen HYSYS: thermodynamic packages, flowsheets, case studies, debottlenecking and keeping models matched to the plant.

  1. Simulation basis and model purpose statement
  2. Thermodynamic package selection for your system
  3. Component list and hypothetical components set-up
  4. Feed characterisation from assay and lab data
  5. Units, conventions and starter simulation template
  6. First steady-state model of a single separator train
  7. Hand calculation checks against the simulator
  8. Convergence and recycle strategy for the flowsheet
  9. Model file naming, versioning and storage
  10. Monthly plant data reconciliation against the model
  11. Model-to-plant match tracking log
  12. Simulation licence and software version register
  13. Model change log and weekly peer check
  14. Case study request intake for operations and projects
  15. Heat exchanger fouling update in the model
  16. Column efficiency and tray performance retuning
  17. Site simulation model library and status register
  18. Yearly model revalidation after the turnaround
  19. Equations of state for simulation users
  20. Activity coefficient models and interaction parameters
  21. Distillation column specification and convergence
  22. Optimiser and sensitivity analysis tools
  23. Rigorous heat exchanger rating inside the flowsheet
  24. Dynamic simulation basics, pressure-flow and holdups
  25. Phase envelope, hydrate and solids checks
  26. Debottlenecking study for a rate increase
  27. Energy and utility reduction case study
  28. Steady-state or dynamic model for the question
  29. Choosing a process simulator for the team
  30. Property data gaps and lab measurement request
  31. Reducing model run time and fragility
  32. Automated case runs from a spreadsheet or script
  33. Simplified surrogate model for operations use
  34. Heat and material balance issue for a FEED package
  35. New feed source impact study before switchover
  36. Model handover from project to operations
  37. Presenting simulation results to plant management
  38. Performance test prediction before a plant test run
  39. Graduate's first ninety days with the simulator
  40. Operations engineer running models part time
  41. Inheriting a model built by someone who has left
  42. Simulation consultant delivering work for a client
  43. Lead simulation engineer on a multi-discipline project
  44. Dynamic depressuring and blowdown simulation
  45. Dynamic model for testing a control scheme
  46. Operator training simulator scope and validation
  47. Online model and real-time optimisation readiness
  48. Reactor model with kinetics fitted to plant data
  49. Refrigeration and liquefaction cycle model
  50. Writing a site simulation practice guide

Where it starts.

Each project arrives with its purpose, milestones and first tasks written out. Here is how the first three read.

Simulation basis and model purpose statement

Most bad simulations fail before the first stream is drawn, because nobody wrote down what question the model must answer, at what accuracy, and over what operating range. A two-page simulation basis fixes the scope boundary, the cases, the property method, the data sources and the acceptance tolerances, so reviewers check the model against a promise rather than a feeling.

First tasks

  • Write the three questions the model must answer and who will act on each
  • Mark the model scope boundary and tie-ins on the latest PFD
  • Draft the simulation basis with cases, data sources and accuracy targets
  • Send the basis to the process lead and record their acceptance

Thermodynamic package selection for your system

Picking Peng-Robinson because it was the default is the commonest silent error in process simulation, and it can move a dew point, a column split or a solvent loss far enough to change a design. Choosing the property method deliberately, by component family, pressure range and phase behaviour, and recording why, is the single decision that most affects whether the model is believable.

First tasks

  • List the component families and the pressure and temperature range in scope
  • Read the simulator's property method selection guide for your system type
  • Compare two candidate methods against one published data set
  • Record the chosen method and its limits in the simulation basis

Component list and hypothetical components set-up

Every component you leave out or lump together carries through every stream in the model, so a missing trace of hydrogen sulphide or mercury can hide a corrosion or specification problem completely. Building the component list on purpose, with hypothetical or pseudo components defined from real data where library ones do not exist, gives a component slate the whole team can reuse.

First tasks

  • Collect the latest lab analyses for every feed and product in scope
  • List components that drive specification, safety or corrosion limits
  • Define each hypothetical component and note where its properties came from
  • Save the component slate as a reusable file in the model library

Make it yours.

Install Process Simulation Modelling, then tell Aurum the date you're aiming for. It checks whether the plan fits the weeks you actually have.

Free · Mac (Apple silicon) and Windows · v1.0.5 · Other platforms

Blueprints are general information to help you organise your own work. They are not medical, financial, legal or other professional advice. See the Terms.